Evolution 2 CD Player

Our entry level CD Player

Leaflet - Instructions - Images

The EVOLUTION 2 CD Player, which went into full production at the beginning of 2009, is the latest incarnation of Creek Audio’s successful entry level EVOLUTION CD Player.

The EVOLUTION 2 builds upon the strengths of the original by replacing older technology parts and retaining the best bits, to enhance its overall performance. It is designed to cosmetically match the EVOLUTION 2 Integrated Amplifier, although it will work perfectly with any make hi-fi amplifier.

The EVOLUTION 2 CD Player is housed in a large steel and aluminium case and finished in either a brushed silver or black 12mm thick front panel. Rubber isolation feet help to prevent mechanical vibrations from interfering with its high quality performance. It is physically the same size as the earlier model and matches the tuner and slightly larger integrated amplifier.

At the heart of a good CD Player is a high quality transport mechanism. The EVOLUTION 2 uses a dedicated CD transport mechanism comprising of custom made drawer loader and high quality laser assembly. Soft rubber bushes help to maintain playability under conditions of mechanical vibration. This brings improved playability strength and smoothness to its operation not bettered by CD players at any price.

Suggested System

sounds good with

The Evolution 2 CD Player will work very well in the following system. Please note the speakers quoted may need to be different depending on the size of room your system is to be used in.

Ampliifer: Evolution 2 Integrated Amplifier

Speakers: Epos Epic 1Epos Epic 2Epos Epic 5

CD decoder and servo motor control functions are performed by a new Philips Compact Disc chip-set. This is now located on a dedicated circuit board mounted directly under the laser assembly for the shortest possible signal routing. This provides the EVOLTION 2 with a self-contained CD transport module. Power supply, digital control, SPDIF output and I2S signals to the DAC are connected to the main board with only two connectors.

The EVOLUTION 2 uses a single high current C core mains transformer, with multiple low voltage output windings, fed from the mains IEC connector via a common mode filter. An external voltage selector allows it to be easily used in all countries. Mains connection is via a standard, fused, IEC chassis plug. A high quality power cord, with suitable mains plug for the country of use is supplied.
To stabilise and isolate the voltages to the various analogue and digital circuits the EVOLUTION 2 uses eight voltage regulators. Digital and analogue power supplies are kept completely separate and even the master clock circuit uses its own power supply.

Technical Specification detailed technical information
Frequency Response 1Hz – 20Khz ± 0.25dB
Output Level 2.0V RMS @ 1KHz, 0dB
Output Impedance 50 Ohm, min load 1 Ohm
DAC Type 24bit – 192Khz Burr-Brown Delta-Sigma
Clock Type Temperature compensated ultra low jitter and phase noise module with re-clocking
THD < 0.0008% @ 1KHz, 0dB
Dynamic Range > 100dB
CD Formats Red Book Standard (CD & CD-R)
Voltage Switchable 115V/230V
Consumption 23W max
Weight 6Kg (13.2lbs)
Finish Colours Silver or Black
Size Size W/H/D 430 x 70 x 340mm

Essential to a good sounding CD player is a low jitter master clock. The EVOLUTION 2 has been designed to use a highly accurate oscillator module that clocks the data from the CD decoder to the D to A converter and also clocks the system microcontroller with the same frequency. This is done to reduce the internal interference that would otherwise cause sonic performance reductions if allowed to run at a different, asynchronous frequency.  The digital I2S data from the decoder is re-clocked to provide a low jitter signal to the DAC.

Every CD player needs a DAC to recover the analogue signal from the digital recording. The EVOLUTION 2 now has a Burr-Brown PCM 1796 DAC circuit, which is capable of 24 bit/192kHz operation. It provides a balanced current output, so it is necessary to convert this into an unbalanced voltage output before it can be used. Creek do this by using a high grade op-amp.
To eliminate digital artefacts from interfering with the analogue sound quality, analogue filtering and impedance buffering are applied to the signal, also with a high grade op-amp. A gold contact relay is used at the output to mute the signal to ground when the player is stopped and paused.

Gold plated RCA analogue and digital output sockets have been chosen to provide a good connection and appearance for a product at its price point. Optical digital output is also available via a standard TOSLINK connector.

The EVOLUTION 2 operates with soft touch buttons on the front panel for Play and Pause, Stop, Open and Close, Track forward, backward and power On/off.
Software controls functions, display and remote control. A visual indication of its status is displayed on a large blue Vacuum Fluorescent Display (VFD).

Photo Gallery

more photos

no images were found

A new Creek system remote (SRC3) has been designed for use with Destiny 2. However, it can also operate the EVOLUTION range and will become the de facto standard with all Creek products manufactured after July 2010.

We have combined a superior set of electronics with sophisticated styling to provide you with a quality product that delivers everything you have come to expect from products manufactured by Creek Audio.